ORTUR Laser Master Serie Firmware Download
Hier bekommen Sie die Firmware für den Laser Master und Aufero Laser Modelle.
Laser Master 1
- Firmware Laser Master 1 V1.4
- Ortur Laser Master Firmware
V1.40 Release Date: 04 January 2021
Fixes: -Pause/Resume issue been corrected. Laser Pause/Resume functions now work as expected; -Corrected False positive [Check Limits] on Pro Motherboards (RJ connector/Vertical buttons boards); Improvements - GRBL Core Upgrade from 1.1f to 1.1h; - Optimization of USB Driver Library. Attempt to address disconect issues/Alarm 3; - Fan Delay ShutDown Function. Fan will Remain on from 30 to 120 seconds, based upon the length of time and maximum power of the just finished engraving. - G-Shock Sensor Algorithm. New algorithm reduces the amount of false positives;
- Firmware Laser Master 1 V1.34
Laser Master 2
- Fimrware Laser Master 2 V1.40
- Ortur Laser Master Firmware
V1.40 Release Date: 04 January 2021
Fixes: -Pause/Resume issue been corrected. Laser Pause/Resume functions now work as expected; -Corrected False positive [Check Limits] on Pro Motherboards (RJ connector/Vertical buttons boards); Improvements - GRBL Core Upgrade from 1.1f to 1.1h; - Optimization of USB Driver Library. Attempt to address disconect issues/Alarm 3; - Fan Delay ShutDown Function. Fan will Remain on from 30 to 120 seconds, based upon the length of time and maximum power of the just finished engraving. - G-Shock Sensor Algorithm. New algorithm reduces the amount of false positives;
- Firmware Laser Master 2 V1.34
Laser Master 2 Pro
- Firmware Laser Master 2 Pro Board V1.55
- Ortur Laser Master 2 Pro Firmware
V1.55 Release Date: 02 August 2021
Fix: - Power-on set PWM to low level - 0V; - Buffer issue fix for High Speed Engraving that would cause motion to become stuttery; - Error 18 error now displays aditional instructions [MSG: Emergency Switch Engaged]; - Motion sensor sensitivity adjusted from 250 to 385 as default; - Enhancing The Auto Unlock status in Lightburn when Stop button is Hit;
Improvements: -Add Audible Hint - 1 or 2 short buzz - if Power button is pressed for 5 seconds but Emergency Switch is Engaged; (This helps users that mistakenly pressed the emergency switch and have no reaction from machine on power up procedures) -Message change on Flame Sensor if user disables by $261=0, [MSG: Warning: Flame sensor Disabled by User OverRide]
- Firmware Laser Master 2 Pro Board V1.53
- Ortur Laser Master 2 Pro Firmware
V1.53 (Official Release) Release Date: 01 June 2021
Fix: - Official Base Firmware 1.53
Improvements: -Added Optional Flame sensor Output data on $259 GRBL Parameter (1=ON; 0=OFF) -Flame Detection Algorithm Improvements, new $260 and $261 base values for better bed coverage
- Firmware Laser Master 2 Pro Board V1.52
- Ortur Laser Master 2 Pro Firmware
V1.52 Release Date: 16 May 2021
Fixes:
-Fix Bug where Shock&Motion detection not triggering machine halt state correctly
Improvements: -Updated Error messages, giving user prompt to troubleshoot steps -Flame Detection algorithm improvements
- Firmware Laser Master 2 Pro Bedienteil V4.2
Laser Master M400
- Firmware Lasser Master M400 V1.40
- Ortur Laser Master Firmware
V1.40 Release Date: 04 January 2021
Fixes: -Pause/Resume issue been corrected. Laser Pause/Resume functions now work as expected; -Corrected False positive [Check Limits] on Pro Motherboards (RJ connector/Vertical buttons boards); Improvements - GRBL Core Upgrade from 1.1f to 1.1h; - Optimization of USB Driver Library. Attempt to address disconect issues/Alarm 3; - Fan Delay ShutDown Function. Fan will Remain on from 30 to 120 seconds, based upon the length of time and maximum power of the just finished engraving. - G-Shock Sensor Algorithm. New algorithm reduces the amount of false positives;
Flash Anleitung DE / EN
Zurück
|